Drill Bits and Drilling

B 15.8mm A 35.4mm  E 11.4mm   45o Chamfering bits are can be used just to break the edge or produce a full decorative cut. By fitting a smaller bea...

Radius 6.4mm A 41.4mm  B 18.0mm   Traditionally the ogee bit routs through the surface of the job.  These ball bearing guided bits follow the conto...

Radius 4.8mm A 35.0mm  B 15.0mm   Traditionally the ogee bit routs through the surface of the job.  These ball bearing guided bits follow the conto...

Radius 9.5mm A 54.0mm  B 25.0mm   Traditionally the ogee bit routs through the surface of the job.  These ball bearing guided bits follow the conto...

Radius 9.5mm A 54.0mm  B 25.0mm   Traditionally the ogee bit routs through the surface of the job.  These ball bearing guided bits follow the conto...

Radius 6.4mm A 41.4mm  B 18.0mm   Traditionally the ogee bit routs through the surface of the job.  These ball bearing guided bits follow the conto...

Radius 4.8mm A 35.0mm  B 15.0mm   Traditionally the ogee bit routs through the surface of the job.  These ball bearing guided bits follow the conto...

Radius 16.0mm A 44.5mm  B 19.0mm   Cove Bits are used for decorative edging and drop leaf table joints.   Revised 9/05/2024     

Radius 12.7mm A 35.0mm  B 15.9mm   Cove Bits are used for decorative edging and drop leaf table joints.   Revised 9/05/2024

Radius 9.5mm A 28.6mm  B 12.7mm   Cove Bits are used for decorative edging and drop leaf table joints.   Revised 9/05/2024     

Radius 6.4mm A 22.0mm  B 12.7mm   Cove Bits are used for decorative edging and drop leaf table joints.   Revised 9/05/2024     

9.5mm Roman Ogee Router Bit Radius 9.5 A - 51mm B - 25mm The Roman Ogee bit is widely used on production of fine furniture. This bit provides a co...

6.4mm Roman Ogee Router Bit Radius 6.4 A - 35mm B - 17mm C - 1/2" Shank The Roman Ogee bit is widely used on production of fine furniture. This bi...

6.4mm Roman Ogee Router Bit Radius 6.4 A - 35mm B - 17mm The Roman Ogee bit is widely used on production of fine furniture. This bit provides a co...

4mm Roman Ogee Router Bit Radius 4.0 A - 30mm B - 12mm The Roman Ogee bit is widely used on production of fine furniture. This bit provides a conv...

Rabbeting bits cut fast accurate rabbet joints which are seen in the draw  front and rear inlet sections in the backs of picture and mirror frames,...

Rabbeting bits cut fast accurate rabbet joints which are seen in the draw front and rear inlet sections in the backs of picture and mirror frames, ...

8,9.5,11,12.7 Rabbeting Set1/2 Rabbeting bits cut fast accurate rabbet joints which are seen in the draw  front and rear inlet sections in...

Rounding Over Bits are the most used of all the edge forming router bits. They are used for just breaking the sharp edge on a job as well as cuttin...

Rounding Over Bits are the most used of all the edge forming router bits. They are used for just breaking the sharp edge on a job as well as cuttin...

Rounding Over Bits are the most used of all the edge forming router bits. They are used for just breaking the sharp edge on a job as well as cuttin...

Rounding Over Bits are the most used of all the edge forming router bits. They are used for just breaking the sharp edge on a job as well as cuttin...

Rounding Over Bits are the most used of all the edge forming router bits. They are used for just breaking the sharp edge on a job as well as cuttin...

Rounding Over Bits are the most used of all the edge forming router bits. They are used for just breaking the sharp edge on a job as well as cuttin...

Rounding Over Bits are the most used of all the edge forming router bits. They are used for just breaking the sharp edge on a job as well as cuttin...

Rounding Over Bits are the most used of all the edge forming router bits. They are used for just breaking the sharp edge on a job as well as cuttin...

Rounding Over Bits are the most used of all the edge forming router bits. They are used for just breaking the sharp edge on a job as well as cuttin...

Rounding Over Bits are the most used of all the edge forming router bits. They are used for just breaking the sharp edge on a job as well as cuttin...

Rounding Over Bits are the most used of all the edge forming router bits. They are used for just breaking the sharp edge on a job as well as cuttin...

Rounding Over Bits are the most used of all the edge forming router bits. They are used for just breaking the sharp edge on a job as well as cuttin...

Rounding Over Bits are the most used of all the edge forming router bits. They are used for just breaking the sharp edge on a job as well as cuttin...

Rounding Over Bits are the most used of all the edge forming router bits. They are used for just breaking the sharp edge on a job as well as cuttin...